Skip to content

Australia

What is DSCR and how is business loan serviceability assessed?

The debt service coverage ratio (DSCR) is the business's earnings available for debt divided by a year of loan repayments, principal and interest. A DSCR of 1.0 means earnings exactly cover the repayments with nothing to spare; published guides put the common commercial lender benchmark at 1.25 or above. Lenders usually test it at a buffered interest rate and look at it alongside interest cover and total debt to earnings.

Updated · Lende

The formula

DSCR = earnings available for debt service ÷ total debt service.

Total debt service is a year of repayments on every facility the business will carry after the deal: principal and interest on amortising loans, interest on interest-only loans and lease payments. Existing debts that aren't being refinanced count too.

What goes on top varies by lender. The usual definition is net operating income: revenue less operating expenses, before interest and tax. For a trading business that is close to normalised EBITDA, with the owners' wages counted as a cost at a market rate.

Some brokers also show a stricter cash view that takes off income tax and any owners' drawings above the wages already counted, since that money isn't available for repayments either. It gives a lower figure, so say which version you show. Published benchmarks are quoted on the usual definition.

Reading the ratio

Each lender sets its own minimum, which can move with the economy and the loan type.
DSCRWhat it means
Below 1.0Earnings don't cover the repayments
1.0Earnings exactly cover the repayments, with no buffer
1.25 or aboveThe benchmark published guides quote for commercial lenders
HigherMore room for a bad year or a rate rise

Buffers and sensitivity

Lenders usually assess repayments at a rate above the actual one, so the loan still works if rates rise. Work out the DSCR at both the actual and the buffered rate. Then show what happens at one, two and three points higher. The buffer each lender uses is its own policy.

The other ratios

  • Interest cover: EBITDA ÷ a year's interest. Shows how comfortably earnings meet the interest alone.
  • Debt to EBITDA: total debt after the deal ÷ EBITDA. How many years of earnings the debt represents.
  • Loan to value (LVR): secured debt ÷ the value of the security.

A worked example

Made-up figures for a business borrowing to buy equipment:

Normalised EBITDA$400k2.50 timesCash after tax and drawings$220k1.38 timesDebt service $160k a year
Made-up figures. The dashed line is a year of repayments: the further past it the bar runs, the more room there is.
Example only. $400,000 ÷ $160,000, then $220,000 ÷ $160,000. At a higher assessment rate the repayments rise and both ratios fall.
LineAmount
Normalised EBITDA (owners' wages counted at market rate)$400,000
Repayments on the new loan (a year)$110,000
Repayments on the existing loan (a year)$50,000
Total debt service$160,000
DSCR on EBITDA2.50 times
Less income tax($60,000)
Less owners' drawings above their wages($120,000)
Cash left for debt service$220,000
Stricter cash DSCR1.38 times

Common mistakes

  • Leaving out existing debts that stay in place.
  • Counting the owners' wages twice: once as a cost in EBITDA, then again as drawings.
  • Using one good year when the trend is down.
  • Using SDE: lenders count the owners' wages as a cost.
  • Testing only at the actual rate.
  • Presenting the ratio as a verdict. The lender decides; the paper shows the working.

General information, not credit or financial advice. Each lender sets its own policy and makes its own decision.

Questions

Also asked.

What is a good DSCR?
Published guides quote 1.25 or above as the common benchmark for commercial lenders. The lender's own policy decides. It can vary by loan type and economic conditions.
Does DSCR use EBITDA or net profit?
It depends on the lender. The usual definition is net operating income, before interest and tax, which for a trading business is close to EBITDA. A stricter cash view also takes off tax and owners' drawings.
Why do lenders add a buffer to the rate?
To test that the business can still repay if interest rates rise. The size of the buffer is set by each lender.
Is DSCR the only thing a lender looks at?
No. Security, the borrowers' history, the ATO position, the industry and the people all count. DSCR is one measure among several.

Sources

Where Lende helps

Spend the time on the deal, not the paperwork.

14 days free for your whole team. No card needed.